WAKOL Z 520 Thin Screed, fibre-reinforced Fibre-reinforced, very low-tension, self-levelling, cement-based thin screed, for offsetting unevenness in layer thicknesses between 3 - 40 mm

In stock - Delivery by 9th December

Description / WAKOL Z520 Thin Screed 22kg

WAKOL Z 520 Thin Screed, fibre-reinforced Fibre-reinforced, very low-tension, self-levelling, cement-based thin screed, for offsetting unevenness in layer thicknesses between 3 - 40 mm

• Textile flooring

• Resilient flooring

• Parquet (minimum thickness of 3 mm)

• for internal use

Subfloors

The subfloor as well as the room climate conditions must meet the requirements of the applicable standards and data sheets. Subfloors must be permanently dry, solid, free from cracks, dirt and adhesion-inhibiting substances. Use a suitable mechanical procedure to remove separating layers.

Prime cement paving, calcium sulphate concrete, concrete and other absorbent subfloors with WAKOL D 3040 Primer Concentrate, diluted 1:2 with water, or with WAKOL D 3035 Dispersion Primer. Always comply with primer drying times.

When applying WAKOL Z 520 Thin screed, fibre-reinforced to wooden floors like plywood a maximum levelling thickness of 6 mm is possible. Use WAKOL D 3045 Special primer on wooden floors exclusively.              

New, well sanded, standardized cast asphalt concrete does not require a primer when applying to a maximum depth of 10mm. Prime worn and poorly sanded cast asphalt concrete (according to standard) with WAKOL D 3040 Primer Concentrate, diluted 1:1 with water, or with WAKOL D 3035 Dispersion Primer.

 

Usage

Stir WAKOL Z 520 Thin Screed, fibre-reinforced in a clean mixing vessel with 3,5-3,75 liters of clear, cold tap water until free of lumps. The mixing device must not exceed 600 rpm. Using a pin knife, dripper, or smoothing trowel, uniformly apply the mixed compound to the subfloor in the desired layer thickness (at least 3 mm). We recommend using a spiked roller l. Before applying the levelling compound, check whether a sufficiently sized edge strip is available.

Protect the levelling compound layer from direct sunlight and draughts while it sets.

  • - This levelling compound can be applied in layer thicknesses from 3 to 40 mm,
  • - Easy to process
  • - Very good flow
  • - Dries very quickly
  • - Fiber-reinforced

 

Important

Processing not below floor temperature of +15 °C and room temperature of +18 °C, as well as room humidity preferably between 40 % and 65 %, maximum 75 %. All information is based on approx. 20 °C and 50 % relative air humidity. Acclimatize all laying materials before installation in these conditions.

When applying the levelling compound in a layer thickness over 5 mm on calcium sulphate- bonded screeds, use only Wakol reaction primer such as WAKOL PU 280 Polyurethane Primer. Please consult the corresponding data sheet.

The permissible layer thickness over timber substrates is 6 mm, over mastic asphalt (IC10 and IC15) the max. is 10 mm.

We guarantee the uniform high quality of our products. All data is based on tests and many years of practical experience and refers to standardized conditions. The variety of materials used and the different construction site conditions, which lie beyond our control, preclude any claims based on this data. We therefore recommend making sufficient trials. Accompanying flooring manufacturer's instructions and the currently applicable codes must be observed. We gladly provide technical advice.

The product data sheets can be found in their latest version at www.wakol.com. This Technical Information of 12.02.2021 supersedes all previous versions.

 

Technical data

Mixture:                                             3,5-3,75 l water + 22 kg WAKOL Z 520 Thin Screed

Working time:                                   approx. 30 minutes

Suitable for Walking:                      approx. 2 hours

Waiting time before laying:            3-5mm minimum 6 hours

>5mm up to 40mm minimum 48 hours

Storage time:                                   12 months: Store in a cool dry location

Storage temperature:                     not sensitive to frost

EN 13818: 2002:                               CT-C30-F8 CT

Consumption:                                   1,8kg/m²/mm

More Information

Product name 159390
Brand Wakol
Accessory type Sub-floor Preparation

Downloads

Related Products

Navigating through the elements of the carousel is possible using the tab key. You can skip the carousel or go straight to carousel navigation using the skip links.
55mm Acoustic Bases (Box 120)
Request Price
Wakol MS 228 Parquet adhesive 18kg
£91.99 each inc. VAT
Wakol D3055 Universal Primer 10KG
£71.99 each inc. VAT
Wakol MS330 Silane Primer
£130.49 each inc. VAT

We found other products you might like!

Navigating through the elements of the carousel is possible using the tab key. You can skip the carousel or go straight to carousel navigation using the skip links.
55mm Acoustic Bases (Box 120)
Request Price
Wakol MS 228 Parquet adhesive 18kg
£91.99 each inc. VAT
Wakol D3055 Universal Primer 10KG
£71.99 each inc. VAT
Wakol MS330 Silane Primer
£130.49 each inc. VAT
loader
Loading...